Installation, Care and Cleaning Model WB-2218 Palladio
Tools Required:
•
Ruler/Tape Measure
• Drill
•
Masking Tape
•
Safety Glasses
• Screwdriver
•
Saber Saw
•
Caulk/Silicone Adhesive
MASKING TAPE
N
OTE:
DEPENDING ON THE SURFACE THAT YOU WILL BE MOUNTING
THIS PRODUCT INTO, YOU WILL NEED THE NECESSARY TOOLS
REQUIRED TO CUT INTO THAT SURFACE.
You will need tools required to install a faucet. Check the faucet manufacturer’s installation procedure. If
y
o
u will be mounting the faucet into the Swanstone, you will need a 1/4” drill bit and a 1-1/4” router, spade
bit, twist drill or hole saw.
Drill Starter Hole
Inside of Cut Out
Area
N
OTE
If you will be installing a faucet
i
nto this Swanstone product,
m
odel W
B-2218, you will need to
follow this procedure.
T
he Swanstone bowl comes with
standard hole patterns. Locate
the desired drill points and with
a
1/4” bit, drill a pilot hole from
the underside.
D
rill fixture holes from the top
w
ith a 1-1/4” router, spade bit,
twist drill or hole saw. Faucets
may be installed at this time.
I
I
M
M
P
P
O
O
R
R
T
T
A
A
N
N
T
T
USE ROUTER, SPADE BIT, TWIST
DRILL OR HOLE SAW ONLY.
C
C
A
A
U
U
T
T
I
I
O
O
N
N
DO NOT USE AN AUGER BIT.
Instructions For Drilling Into The Swanstone Product
1. C
ut out the inside of the template.
L
ocate the template front to rear and
right to left on the countertop. Make
sure that the bowl location will not
i
nterfere with the cabinet below or the
plumbing. Attach the template to the
countertop with masking tape and draw
a pencil line around the inside of the
template.
2. D
rill a starter hole inside of the
c
utout line.
3. Using a saber saw, cut inside of
the cutout line. Trial fit to check for
pro
per fit.
4. For final fit, apply a bead of caulk
(not included) to the underside of the
sink flange and position onto the coun-
tertop opening. First, tighten screws in
front, and then tighten rear screws.
5. Connect all faucet supply lines and
drain fittings per manufacturer's instruc-
tions.
RECOMMENDED CLEANING PROCEDURE FOR SWANSTONE SOLID SURFACE
H
ard to Remove Stains
1. Abrasive cleaners such as Ajax, Comet, Bon Ami or Bar Keeper's Friend.
2. The use of an abrasive pad such as "Scotch-Brite."
3. For the most stubborn stains, fill the Swanstone vanity bowl about one-quarter full with a 50/50 solution of bleach and water. After ten or fifteen minutes of soaking, drain solution from the bowl as you wash and rinse both
sides and bottom.
NOTE: DO NOT USE STEEL WOOL OR METAL SCOURING PADS.
Mineral Based Stains
Cleaners designed to remove iron or rust should not harm Swanstone.
Marks or Discoloration
WHITE automotive rubbing compound may be used to remove stubborn marks or discoloration.
Scratches
U
se sandpaper starting with 150 grit followed by 220 grit and then 320 grit. Finally, blend area in using a Scotch-Brite pad until scratch disappears.
NO
TE:
FOR SW
ANSTONE GRANITES, use #9 Fine Finishing Film for final blending. Use Paste Wax to restore color.
Use of these products will not damage the Swanstone solid surface. Always follow label directions. If these methods fail to produce acceptable results, contact the Swan representative in your area.
The Swan Corporation One City Centre Suite 2300 St. Louis, MO 63101 800-325-7008
Form #852-6--05-00M
CENTER LINE
C
ENTER LINE BACK
CENTER LINE
CENTER LINE
FRONT
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals